Free 200-101: Interconnecting Cisco Networking Devices Part 2 (ICND2) Exam Questions and Answers

Refer to the exhibit. Austin# hostname Austin username Dallas password Tx4829 ! interface Serial0/0/0 ip address 10.1.1.1 255.255.255.252 encapsulation ppp ppp authentication chap clock rate 64000 Dallas# hostname Dallas username Austin password Tx4892 ! interface Serial0/0/0 ip address 10.1.1.2 255.255.255.252 encapsulation ppp ppp authentication chap The DCE end of the cable is connected to Austin. Serial0/0/0 is up on both routers, but the line protocol is down and the routers cannot ping each other. Which statement identifies the cause of the problem?

• AA. The ppp authentication chap command must be removed from one of the two routers
• BB. The clock rate command must also be configured on the Dallas serial interface
• CC. The hostname configured on each router must be identical for CHAP to authenticate
• DD. The password in the username entry on Austin differs from the one on Dallas

A router learns of network 10.20.0.0/16 from RIP, OSPF, internal EIGRP and external EIGRP. All protocols use their default administrative distance values. Which route is installed in the routing table?

• AA. The route learned from RIP
• BB. The route learned from OSPF
• CC. The route learned from external EIGRP
• DD. The route learned from internal EIGRP

An administrator needs a router to collect NetFlow statistics for traffic that is received on GigabitEthernet0/1. Which command, entered in interface configuration mode, starts the collection?

• AA. ip flow-top-talkers
• BB. ip flow egress
• CC. ip flow-export destination 192.0.2.50 2055
• DD. ip flow ingress

Refer to the exhibit. R1# router eigrp 100 network 10.10.10.0 0.0.0.3 no auto-summary ! interface Serial0/0/1 ip address 10.10.10.1 255.255.255.252 R2# router eigrp 100 passive-interface Serial0/0/1 network 10.10.10.0 0.0.0.3 no auto-summary ! interface Serial0/0/1 ip address 10.10.10.2 255.255.255.252 The Serial0/0/1 interfaces are up and the routers can ping each other. R1 and R2 do not form an EIGRP neighbor relationship. What is the cause of the problem?

• AA. The passive-interface command on R2 suppresses EIGRP hello packets on the link
• BB. The bandwidth command must be configured on both serial interfaces
• CC. The no auto-summary command must be removed from both routers
• DD. The network statement on R1 has a wildcard mask that excludes its serial interface

An administrator must export NetFlow records from a router to a collector at 192.0.2.50. The collector listens on UDP port 2055 and requires version 9 records. Which two global configuration commands are required to configure the export? (Choose two.)

Select 2 answers.

• AA. ip flow-export version 9
• BB. ip flow-export collector 192.0.2.50 udp 2055
• CC. ip flow-export destination 192.0.2.50 2055
• DD. ip flow-cache timeout active 5
• EE. ip flow ingress

Refer to the exhibit. R1# show running-config interface serial 0/0 interface Serial0/0 ip address 10.2.2.1 255.255.255.0 encapsulation frame-relay frame-relay map ip 10.2.2.2 201 broadcast R1# show frame-relay pvc PVC Statistics for interface Serial0/0 (Frame Relay DTE) DLCI = 102, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0 R1 cannot ping 10.2.2.2, the address of the remote router. Which statement explains the problem?

• AA. The frame-relay map command must be replaced with an Inverse ARP configuration to reach 10.2.2.2
• BB. The static map references DLCI 201, but the only active PVC on the interface is DLCI 102
• CC. The broadcast keyword in the map statement prevents unicast traffic from reaching 10.2.2.2
• DD. The serial interface must use the ietf encapsulation type to forward traffic over an active PVC

A switch runs PVST+ with default timers. Port Fa0/3 is in the blocking state because it is an alternate path to the root. The primary link between the root bridge and another switch fails, so Fa0/3 stops receiving BPDUs from the designated bridge. How long does it take Fa0/3 to move to the forwarding state?

• AA. 20 seconds
• BB. 30 seconds
• CC. 35 seconds
• DD. 50 seconds

R1 runs OSPF process 10. Interface GigabitEthernet0/1 connects only to the user LAN 192.168.10.0/24, and that network must still be advertised to other OSPF routers. Which configuration stops R1 from sending OSPF hello packets out GigabitEthernet0/1?

• AA. R1(config-router)# no network 192.168.10.0 0.0.0.255 area 0
• BB. R1(config-router)# passive-interface gigabitethernet0/1
• CC. R1(config-if)# ip ospf priority 0
• DD. R1(config-if)# ip ospf network point-to-point

Refer to the exhibit. R1# show running-config | include ip route ip route 172.16.50.0 255.255.255.0 10.0.0.6 100 R1# show ip route 172.16.50.0 Routing entry for 172.16.50.0/24 Known via "static", distance 100, metric 0 Routing Descriptor Blocks: * 10.0.0.6 Route metric is 0, traffic share count is 1 R1 has a full OSPF adjacency with R3 (10.0.0.2), and R3 advertises 172.16.50.0/24 to R1. The administrator intended the static route to be used only if the OSPF route is lost, but R1 forwards traffic through 10.0.0.6. Why is the static route used?

• AA. The next hop of the OSPF route is unreachable, so the OSPF route is not installed in the routing table.
• BB. The static route has a directly connected next hop, so it takes priority over any OSPF route.
• CC. The static route has an administrative distance of 100, which is lower than the default distance of OSPF.
• DD. The static route has a metric of 0, which is lower than the OSPF cost to the same network.

During password recovery on a Cisco router, an administrator enters ROMmon and sets the configuration register to 0x2142. What happens when the router is reloaded?

• AA. The router loads the IOS image normally but does not load the startup-config from NVRAM.
• BB. The router loads the IOS image from a TFTP server instead of flash memory.
• CC. The router starts in ROMmon and waits for an IOS image to be loaded manually.
• DD. The router erases the startup-config in NVRAM before loading the IOS image.